Free Ground Shipping on orders over $150
  1. Home
  2. Categories
  3. Trailer Axles And Hubs
  4. Trailer Axles

Trailer Drop Axle Painted Steel 3,500lb, 87 in Hub Face Adjustable Spring Seats

Review(s) (1) Write a Review
Part Number: 22113
by Rockwell American: AX358700DC
Steel Drop Spindle Cargo Trailer Axle 3,500 lb Capacity 5 Lug
Feature: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Complete Your Project:

$189.99
In Stock
This 3,500lb Capacity Trailer Drop axle is intended to replace your broken or bent axle on your trailer. A 3,500 lb Capacity Drop Trailer Axle Beam is most commonly used on Enclosed trailers, Cargo Trailers, and Stock Trailers that are running 5 Lug Brake Drums or Idler Hubs, and need to have a lower deck for loading and unloading. This Axle includes standard 4 Hole Brake Flanges welded to the axle beam for mounting Drum and Disc Brakes. 
You would need a replacement axle if you have noticed tread wear due to improper tire alignment, which is the result of a bent trailer spindle on one side. In addition, another common reason for axle damage results from over loading the trailer, which will result in noticing tread wear on the insides of both trailer tires. If you trailer experiences exposure to corrosive environments, such as a boat trailer, rust damage is another possible culprit for axle replacement. 
This 3,500 lb Capacity Trailer Drop Axle is made with 3/16" Steel Wall Thickness, measures 2 3/8" in diameter, and features #84 Spindles welded into the beam. This listing is for the Beam Only. This Axle is for trailers with a Leaf Spring Suspension. We offer all additionally needed components separately for you to build the exact axle kit that you are needing for your trailer.
This Drop Portion of this axle is the Trailers Spindle. The Spindle has a 4 inch Drop to it, which is then Welded into the Beam of the axle. This Drop lowers the Frame of the Trailer 4 inches. Typically you would be replacing a Drop axle with a Drop Axle. If you are going from a Straight axle to a Drop Axle, you would see your Frame, and Fenders, drop 4 inches, so some adjustments might need to be made. 
The Tapered Spindle design of this 3,500 lb Drop Axle has the following features:
 
Inner Bearing Surface: 1 3/8" ( Accommodates Bearing 68149)

Outer Bearing Surface: 1 1/16" ( Accommodates Bearing 44649)

Grease Seal: 1.72" Grease Seal Surface

This Listing is for a 87" Hub Face Axle that does not have the Spring Seats welded to the Axle. The Picture with this listing shows spring seats mounted to the axle, which is just for the purpose of a product photo. This Axle will not have the spring seats welded to the beam, but they are included with the purchase of the axle. This 87 inch measurement is also referred to as the Track Measurement, or Center of Tire Measurement.  

Specific Axle Specifications for this 3,500 lb Trailer Drop Axle:

Hub Face: 87"
*Refers to the Outside Face of one Hub as it meets the wheel to the outside face of opposing hub as it meets the wheel

Brake Flange Measurement: 81"
*Refers to the Outside of one Brake Flange to the outside of opposing brake flange

Overall Axle Length (Tip to Tip): 92"
*Refers to the tip of one side of axle spindle to the opposing tip

Acceptable Spring Seat Ranges: 70" - 74.5" 
*Refers to Measurement from Center of One Leaf Spring to Center of Leaf Spring on opposing end of axle beam
*Per Manufacturer Specifications, for this Axle to achieve its 3,500 lb carrying capacity, this length of axle should only be used within the above mentioned Spring Seat Ranges. Using this axle with Spring Center measurements outside this range could result in improper fit (clearance) or premature axle damage (result of increased leverage). 

Camber: Cambered, Axle Camber is intended for use with Leaf springs mounted below or above the axle.

Spring Seat Location: Included Spring Seats can be welded for Over Slung or Under Slung Leaf Springs.  

Trailer Axle Project Check List:

 
  Leaf Spring U-Bolt Kits – These typically rust or wear out at the same rate as the axle, requiring cutting or breaking during removal.  These kits will re-mount your new axle to your trailers leaf springs.  

   Trailer Leaf Springs  – Replacing rusted or broken leaf springs is crucial to prevent pre mature failure and damage to your suspension system and trailer tires.

   Leaf Spring Mounting Bolts – These Bolts secure your trailers leaf springs to your frame mounted Leaf spring hangers. They are commonly worn and replaced while the trailers leaf springs are being replaced.

   Trailer Leaf Spring Shackles – These shackles are used with Double Eye Leaf Springs to provide the needed suspension for your trailer, held together by the above Leaf Spring Mounting Bolts.

  Trailer Hubs & Parts- Including wheel bearings and grease seal, we have these hubs and brake drums in 5 Lug including the 1 3/8" x 1 1/16" Wheel Bearings for your Axle Kit.
   Trailer Dust Caps - New Dust Caps or Bearing Buddies provide the needed protection and greasing capabilities to protect your trailers axle and wheel bearings. 
   Trailer Lug Nuts - If your Lug Nuts are badly rusted, we have Stainless Steel Lug Nuts available to prevent that issue permanently, and also protect your Hub Studs. 

CUSTOMERS ALSO VIEWED

Price: $0.99
In Stock
(0)
Price: $319.99
In Stock
(0)
Price: $27.99
In Stock
(1)
Price: $362.99
In Stock
(0)
TOP