Trailer Axle Painted Steel with 5 Lug Hubs 3,500lb, 89 in Hub Face - 74 in Spring Center

Part Number: 26233

by Suretrac: 26233

Painted Black Steel 3,500lb Trailer Axle with Idler Hubs

Feature: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Quantity	Price
1 - 3	$366.50
4 - 7	$266.56
8 - 15	$252.78
16+	$244.35

Price $366.50

Quantity

In Stock

Description

This 3,500 lb black painted steel axle has a hub face measurement of 89 inches and features prepacked and greased painted idler hubs, ready to install and replace your old bent or broken axle! The axle features standard 4 hole brake flanges, allowing you to mount most brands of brakes, such as those made by Kodiak, Deemaxx, Tie Down, and Titan. The spindle of the axle includes a greaseable zerk fitting, allowing you to relubricate the bearings without needing to disassemble the hubs and pack the bearings by hand. You would need a replacement axle if you have noticed tread wear due to improper tire alignment, which is the result of a bent trailer spindle on one side. In addition, another common reason for axle damage results from overloading the trailer, which will result in noticing tread wear on the insides of both trailer tires. If your boat trailer experiences exposure to corrosive environments, rust damage is another possible culprit for axle replacement. This 3,500 lb Capacity Trailer Axle is made with 3/16" Steel Wall Thickness, measures 2 3/8" in diameter, and features #84 Spindles welded into the beam. This listing is for the axle beam and preinstalled hubs, but we carry all of the leaf springs and other components that you need to complete your trailer repair!

The black painted idler hubs on this 3,500 lb Axle have the following features:

Inner Bearing Surface: 1 3/8" (Bearing 68149)

Outer Bearing Surface: 1 1/16" (Bearing 44649)

Grease Seal: 1.72" Inner Diameter Grease Seal Surface

Hub Bolt Pattern: 5 lug on 4 1/2" Bolt Pattern fits most 5 bolt trailer wheels

Dust Caps: 1.98" Accu-lube style zinc-plated dust caps with a removable plug to access grease zerk fitting

This Listing is For an 89" Hub Face Axle that has the Spring Perches welded at 74". This 89-inch Measurement is also referred to as the Track Measurement, or Center of Tire Measurement.

Specific Axle Specifications for this 3,500 lb Trailer Axle:

Hub Face: 89"

*Refers to the Outside Face of one Hub as it meets the wheel to the outside face of the opposing hub as it meets the wheel

Brake Flange Measurement: 83"

*Refers to the Outside of one Brake Flange to the outside of opposing brake flange

Overall Axle Length (Tip to Tip not including hubs and dust caps): 94"

*Refers to the tip of one side of axle spindle to the opposing tip

Camber: Cambered, Axle Camber is intended for use with Leaf springs mounted below the axle.

Spring Seat Location: Spring Seats are welded at 74", this would mean that your Center of Leaf Spring Measurement would be 74"

Trailer Axle Project Check List:

		Leaf Spring U-Bolt Kits – These typically rust or wear out at the same rate as the axle, requiring cutting or breaking during removal. These kits will re-mount your new axle to your trailers leaf springs.
		Trailer Leaf Springs – Replacing rusted or broken leaf springs is crucial to prevent pre-mature failure and damage to your suspension system and trailer tires.
		Leaf Spring Mounting Bolts – These Bolts secure your trailer's leaf springs to your frame-mounted Leaf spring hangers. They are commonly worn and replaced while the trailer's leaf springs are being replaced.
		Trailer Leaf Spring Shackles – These shackles are used with Double Eye Leaf Springs to provide the needed suspension for your trailer, held together by the above Leaf Spring Mounting Bolts.
		Trailer Lug Nuts - If your Lug Nuts are badly rusted, we have Stainless Steel Lug Nuts available to prevent that issue permanently, and also protect your Hub Studs.

Trailer Axle Painted Steel with 5 Lug Hubs 3,500lb, 89 in Hub Face - 74 in Spring Center

Wholesale PRICING:PRICING:

Wholesale PRICING:
PRICING: