Tie Down 9.6 inch Vented Boat Trailer Disc Brake Half Kit 5 Lug Aluminum Caliper

Review(s)(0) Write a Review

Part Number: 24898

by Tie Down Engineering: 46501

Tie Down Engineering 5 Lug Half Disc Brake Kit Vented Rotor and Aluminum Caliper

Feature: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Quantity	Price
1 - 4	$296.40
5	$204.43
6 - 7	$200.96
8 - 9	$197.61
10+	$194.35

Price $296.40

Quantity

In Stock

Description

This is Tie Down Engineerings 9.6 inch Eliminator Vented Integral Rotor Disc Brake Kit for trailers with 3500 lb Axles running 5 Lug Wheels. This Vented Kit mounts to your standard 4 Hole Brake Flange that is on your trailers axle. This Disc Brake Kit will replace 10 inch 5 Lug Brake Drums, or other 5 Lug Disc Brake systems, as long as your axle has a standard 4 Hole Brake Flange.

The All Aluminum Caliper featured in this Kit is the 380 series, which has been tested and proven to shed heat five times than cast iron brake calipers. They are additionally E Coated to prevent salt build up. The Aluminum Caliper features Stainless Steel Backed Ceramic Brake Pads with a Lifetime Limited Warranty. The Trailer Brake Calipers features a bi metal piston system, which integrates an outer stainless steel piston with an inner anodized aluminum sleeve to shed heat faster and provide maximum corrosion resistance when submersed.

The Piston is protected by an Oversized rubber boot, which is 50% thicker to provide more efficient piston withdrawal. Additionally, a rotating brake line connector allows for easy installation of the brake line going into the caliper at multiple angles. Bleeding the brakes is simple and efficient, using the Stainless Steel Bleeder valve located at the top of the caliper.

The Aluminum Brake Calipers are attached to the Galv X caliper bracket with Stainless Steel Slide pins, which are seated in oil-impregnated bronze bushings, for smooth and corrosion resistant floating, allowing your brakes to move freely, yielding optimal braking performance.

Tie Down Vented Disc Brakes Feature Galv X Integral Rotors with Vented Holes, to disperse heat and provide the highest level of rust prevention. The Rotors integrate the Galv X hub and Galv X rotor into one piece. The Hub Features the industry standard 5 on 4 1/2 lug pattern and accepts 1 3/8" ID 68149 Inner wheel Bearing, and 1 1/16" ID 44649 outer wheel bearing. This Rotor will use the industry standard 1.98 Dust cap as well.

This is for 1 Half Kit, so if you need to replace the Brakes on only one side of your trailer, this is a perfect kit for that. It Includes 1 of each piece, so 1 Caliper, 1 Rotor, and 1 Bracket. If you are adding Disc Brakes to your trailer for the first time, or replacing the entire brake setup, you would either want to purchase 2 of these half kits, or you could purchase the full kit on our website here.

These TDE Disc Brakes are additionally not recommended for use with Electric Over Hydraulic Brake Systems.

This Kit includes everything pictured, which will complete one side of your trailer, not both.

Features:

-Half Kit (1 Side of the trailer)

-Aluminum Caliper, Venter Rotor, all helps dissipate heat

-Stainless Steel Backed Brake Pads included in the Caliper

-5 Lug, 4.5" Pattern

-3,500lb Capacity

-Requires 4 Hole Brake Flange

-Bearings not included

Tie Down 9.6 inch Vented Boat Trailer Disc Brake Half Kit 5 Lug Aluminum Caliper

Wholesale PRICING:PRICING:

Wholesale PRICING:
PRICING: